[gmx-users] gromacs on glacier

[Payman Pirzadeh]

Hi Justin,
Since the manual itself was not sufficient, I asked some other people who
are running GROMACS in our group (but they run only on 2 CPUs). Here are the
steps I took to compile the parallel version (I have included my notes that
they told me as well):

Installation
1.	./configure --prefix=/global/home/pirzadeh/gromacs-4.0.4
This line specifies the installation path

2.	Make
3.	Make install
These two commands will make 'grompp' and analysis functions of GROMACS.

4.	Make clean
This command will clean some files generated during installation which are
not needed anymore.

5.	./configure --enable-mpi --disable-nice
--prefix=/global/home/pirzadeh/gromacs-4.0.4
Here we compile the code for parallel version of GROMACS

6.	make mdrun
7.	 make install-mdrun
Now the parallel version of mdrun is built. The analysis functions are found
in 'bin' folder accompanied by 'GMXRC'.

8.	Before running 'grompp' to produce the topology file for simulation,
we should use the command  source
/global/home/pirzadeh/gromacs-4.0.4/bin/GMXRC to specify the path for the
current code.

Sorry for tons of e-mails.

Payman

-----Original Message-----
From: gmx-users-bounces at gromacs.org [mailto:gmx-users-bounces at gromacs.org]
On Behalf Of Justin A. Lemkul
Sent: June 8, 2009 11:12 AM
To: Discussion list for GROMACS users
Subject: Re: [gmx-users] gromacs on glacier



Payman Pirzadeh wrote:
> Hi,
> 
> I had the chance to run the GROMACS 4.0.4 on another cluster. Same 
> problem still persists. But what I found is that it can be run on a node 
> with 2 CPUs, but as soon as the number of nodes are increased to 2, 3, . 
> it will crash. Following are the last lines reported in different files:
> 
> "In the log file of the code":
> 
>  
> 
> There are: 1611 Atoms
> 
> There are: 1611 VSites

All of your atoms are virtual sites?  If so, I would try a simpler test
case, to 
rule out stumbling across some obscure bug.

Also:

> p2_22627:  p4_error: Timeout in establishing connection to remote process:
0
> 

This is an error message from MPICH, not Gromacs.  See, for example:

http://www.mail-archive.com/gmx-users@gromacs.org/msg10968.html

<snip>

> To me, it seems that code can not communicate through more than one 
> node. I am suspicious of doing sth wrong during installation! I tried 
> wiki, but I can not find the documents as before, and I eally do not 
> know in which step I might have gone wrong.
> 

If you suspect you have done something wrong, then post the details of the 
system configuration (hardware, compilers, OS, etc.) as well as a
step-by-step 
record of what you did to compile the software.  If your procedure is sound,

then it helps rule out the possibility that you messed something up.

-Justin

>  
> 
> Payman
> 
>  
> 
> 
> ------------------------------------------------------------------------
> 
> _______________________________________________
> gmx-users mailing list    gmx-users at gromacs.org
> http://lists.gromacs.org/mailman/listinfo/gmx-users
> Please search the archive at http://www.gromacs.org/search before posting!
> Please don't post (un)subscribe requests to the list. Use the 
> www interface or send it to gmx-users-request at gromacs.org.
> Can't post? Read http://www.gromacs.org/mailing_lists/users.php

-- 
========================================

Justin A. Lemkul
Ph.D. Candidate
ICTAS Doctoral Scholar
Department of Biochemistry
Virginia Tech
Blacksburg, VA
jalemkul[at]vt.edu | (540) 231-9080
http://www.bevanlab.biochem.vt.edu/Pages/Personal/justin

========================================
_______________________________________________
gmx-users mailing list    gmx-users at gromacs.org
http://lists.gromacs.org/mailman/listinfo/gmx-users
Please search the archive at http://www.gromacs.org/search before posting!
Please don't post (un)subscribe requests to the list. Use the 
www interface or send it to gmx-users-request at gromacs.org.
Can't post? Read http://www.gromacs.org/mailing_lists/users.php